2016 Truck Inventory

4-1/4" OD. WHITE DOMED PLASTIC CLEANOUT COVER

4-1/4" OD. FLAT WHITE PLASTIC CLEANOUT COVER

3/8 in. MHT Brass Coupling Fitting 802619

40/60 LB WELL PRESSURE SWITCH (LEAD LAW COMPLIANT)

PRIER #630-7500 VACUUM BREAKER REPAIR KIT REPLACES DISCONTINUED #UR025288 NIBCO VAC. BREAKER KITS

JONES C74250LF 3/8IN X 3/8IN SUPPLY STOP EXTENDER TEE (3/8 ADD-A-TEE)

FLUIDMASTER 14 X 14 FRAMELESS ACCESS PANEL

FLUIDMASTER 8 X 8 FRAMELESS ACCESS PANEL

8" X 8" PLASTIC ACCESS PANEL WHITE

3/8C X 1/4C STOP ADAPTER TEE (LEAD LAW COMPLIANT) (ADD-A-TEE)

2 GPM POLISHED CHROME DUAL THREADED AERATOR (12 pak)(Hajoca=6 pak)

GRUNDFOS 92603114 ALPHA CS 15-55 SU7P/TLC ECM HIGH EFFICIENCY COMFORT SYSTEM

42 IN ALUMINUM ANODE ROD FOR HARD WATER

<b>PROVIDE & INSTALL NEW AO SMITH GCRL-50 PROPANE GAS ATMOSPHERIC VENT 40,000 BTU WATER HEATER.</b><br/><br/><b>ABOUT:</b><br/>The ProLine&reg; 400/401 Series gas water heater is designed to deliver an economical performance that can lower your energy bills and also provide long-lasting value.<br/><br/>Featuring a 50-gallon (nominal) tank and a 40,000 BTU gas burner, the GCRL-50 Standard Vent delivers a first hour rating of 81 gallons and a recovery rate of 41 gallons per hour. With an 0.62 Uniform Energy Factor, this water heater is not ENERGY STAR&reg; qualified. It carries a 6-year limited tank warranty, and meets Low NOx emission requirements.<br/><br/><b>INCLUDES:</b><br/><ul><li>INSTALLATION OF NEW WATER HEATER TO REPLACE SIMILAR WATER HEATER.<br/></li><li>INSTALLATION OF NEW SHUTOFF VALVE TO SERVE NEW WATER HEATER.<br/></li><li>MISC PIPE & FITTINGS IN ORDER TO CONNECT NEW WATER HEATER TO EXISTING DOMESTIC HOT & COLD WATER PIPING.<br/></li><li>MISC PIPE & FITTINGS IN ORDER TO CONNECT NEW WATER HEATER TO EXISTING GAS PIPING.</li></ul><br/><b>EXCLUDES:</b><br/><ul><li>CARBON MONOXIDE DETECTORS.<br/></li><li>THERMAL EXPANSION TANK.<br/></li><li>PRESSURE REDUCING VALVE.</li><li>WATER HEATER STAND.<br/></li><li>WATER HEATER PAN AND / OR PAN DRAIN PIPING.<br/></li><li>PIPING OF TEMPERATURE & PRESSURE RELIEF VALVE TO THE EXTERIOR.<br/></li><li>VENT REPAIR AND / OR REPLACEMENT (SHALL CONNECT NEW WATER HEATER TO EXISTING VENT).</li></ul><br/><b>DIMENSIONS: </b><br/><ul><li>53in TALL </li><li>24in WIDE</li></ul>

<b>PROVIDE & INSTALL NEW AO SMITH GCRL-50 NATURAL GAS ATMOSPHERIC VENT 40,000 BTU WATER HEATER.</b><br/><br/><b>ABOUT:</b><br/>The ProLine&reg; 400/401 Series gas water heater is designed to deliver an economical performance that can lower your energy bills and also provide long-lasting value.<br/><br/>Featuring a 50-gallon (nominal) tank and a 40,000 BTU gas burner, the GCRL-50 Standard Vent delivers a first hour rating of 81 gallons and a recovery rate of 41 gallons per hour. With an 0.62 Uniform Energy Factor, this water heater is not ENERGY STAR&reg; qualified. It carries a 6-year limited tank warranty, and meets Low NOx emission requirements.<br/><br/><b>INCLUDES:</b><br/><ul><li>INSTALLATION OF NEW WATER HEATER TO REPLACE SIMILAR WATER HEATER.<br/></li><li>INSTALLATION OF NEW SHUTOFF VALVE TO SERVE NEW WATER HEATER.<br/></li><li>MISC PIPE & FITTINGS IN ORDER TO CONNECT NEW WATER HEATER TO EXISTING DOMESTIC HOT & COLD WATER PIPING.<br/></li><li>MISC PIPE & FITTINGS IN ORDER TO CONNECT NEW WATER HEATER TO EXISTING GAS PIPING.</li></ul><br/><b>EXCLUDES:</b><br/><ul><li>CARBON MONOXIDE DETECTORS.<br/></li><li>THERMAL EXPANSION TANK.<br/></li><li>PRESSURE REDUCING VALVE.</li><li>WATER HEATER STAND.<br/></li><li>WATER HEATER PAN AND / OR PAN DRAIN PIPING.<br/></li><li>PIPING OF TEMPERATURE & PRESSURE RELIEF VALVE TO THE EXTERIOR.<br/></li><li>VENT REPAIR AND / OR REPLACEMENT (SHALL CONNECT NEW WATER HEATER TO EXISTING VENT).</li></ul><br/><b>DIMENSIONS: </b><br/><ul><li>53in TALL </li><li>24in WIDE</li></ul>

1/2 IN. MIP. BRASS BOILER DRAIN

1/2 IN FIP X MHT BRASS SILLCOCK WITH FLANGE (LEAD FREE)

1/2 IN. PEX X MHT BRASS BOILER DRAIN W/ WHEEL HANDLE

3/4 IN. MIP. BRASS BOILER DRAIN

AMERICAN GRANBY IHBB75NL 3/4 BRASS BOILER DRAIN - 1/4 TURN

3/4 IN FIP X MHT BRASS SILLCOCK WITH FLANGE (LEAD FREE)

1/2 BLACK IRON 45

1/2 BLACK IRON 90

1/2 BLACK IRON COUPLING

1/2 BLACK IRON CAP

1/2" BLACK MI SOLID STEEL OR CORED SQUARE HEAD PLUG

1/2 BLACK IRON STREET 90

1/2 BLACK IRON TEE

1/2 BLACK IRON UNION

3/4" X 1/2" X 3/4" BLACK IRON TEE

3/4" X 1/2" BLACK IRON 90 ELBOW

3/4" X 1/2" BLACK IRON REDUCER COUPLING

3/4" X 3/4" X 1/2" BLACK IRON TEE

3/4" BLACK IRON 45

3/4" BLACK IRON 90

3/4" BLACK IRON COUPLING

3/4" BLACK IRON CAP

3/4" BLACK IRON SOLID OR CORED SQUARE HEAD PLUG

3/4" BLACK IRON STREET 90

3/4" BLACK IRON TEE

3/4" BLACK IRON SWIVEL UNION

2LB CAN BIO CLEAN - FRIENDLY WASTE ELIMINATOR - MIXING CUP - CLEANING TOOL - REMINDER MAGNET SEPTIC TREATMENT

BLACK DUCT TAPE

BLUE MONSTER PIPE DOPE

BLUE MONSTER TEFLON TAPE

BLUE MONSTER HAND WIPES-HEAVY DUTY 12X10

1/2" X 1-1/2" BLACK STEEL NIPPLE

1/2" X 12" BLACK STEEL NIPPLE

1/2IN X 2IN IMP BLACK STEEL NIPPLE

1/2" X 2-1/2" BLACK IRON NIPPLE

1/2" X 3" BLACK IRON NIPPLE

1/2IN X 3-1/2IN IMP BLACK STEEL NIPPLE

1/2" X 4" BLACK IRON NIPPLE

1/2IN X 4-1/2IN IMP BLACK STEEL NIPPLE

1/2" X 5" BLACK IRON NIPPLE

1/2IN X 5-1/2IN IMP BLACK STEEL NIPPLE

1/2" X 6" BLACK IRON NIPPLE

1/2 X 8 BLACK STEEL NIPPLE

1/2IN X CLOSE IMP BLACK STEEL NIPPLE (Hajojoca Alternate = 723 @ $0.941)

1/4" X 3" BLACK IRON NIPPLE

3/4" X 10" BLACK IRON NIPPLE

3/4" X 1 1/2" BLACK IRON NIPPLE

3/4" X 2" BLACK IRON NIPPLE

3/4" X 2 1/2" BLACK IRON NIPPLE

3/4" X 3" BLACK IRON NIPPLE

3/4" X 3 1/2" BLACK IRON NIPPLE

3/4" X 4" BLACK IRON NIPPLE

3/4" X 4 1/2" BLACK IRON NIPPLE

3/4" X 5" BLACK IRON NIPPLE

3/4" X 5 1/2" BLACK IRON NIPPLE

3/4" X 6" BLACK IRON NIPPLE

3/4" X 8" BLACK IRON NIPPLE

3/4" X CLOSE BLACK IRON NIPPLE

<b>PROVIDE & INSTALL NEW BRADFORD WHITE RG2DV50S6 NATURAL GAS 50 GALLON 42K BTU DIRECT VENT WATER HEATER</b><br/><br/><b><u>Features:</u></b><br/><ul><li>Bradford White ICON System&trade;&mdash;Intelligent gas control with proven millivolt powered technology and built-in piezo igniter. A standard, off the shelf thermopile converts heat energy from the pilot flame into electrical energy to operate the gas valve and microprocessor. No need for external electricity.</li><li>Enhanced Performance&mdash;Proprietary algorithms provide enhanced First Hour Delivery ratings and tighter temperature differentials.</li><li>Advanced Temperature Control System&mdash;Microprocessor constantly monitors and controls burner operation to maintain consistent and accurate water temperature levels.</li><li>Intelligent Diagnostics&mdash;An exclusive green LED light prompts the installer during start-up and provides ten different diagnostic codes to assist in troubleshooting.</li><li>Pilot On Indication&mdash;Flashing green LED provides positive indication that pilot is on.</li><li>Separate Immersed Thermowell&mdash;High-strength advanced polymer composite thermowell provides isolation between electric temperature sensor and surrounding water. No need to drain the tank when removing gas valve.</li><li>Closed Combustion&mdash;All air for combustion is taken directly from the outside. The co-axial vent pipe (pipe inside a pipe) draws combustion air in through the outer pipe, and exhausts the products of combustion through the inner pipe. The co-axial vent pipe at the top of the unit can be rotated for venting flexibility.</li><li>Reinforced Seals&mdash;Seals surround the closed combustion chamber and the FVIR inner door, preventing the ignition of flammable vapors outside of the water heater.</li><li>Maintenance-Free&mdash;The vent piping and the closed combustion chamber with reinforced seals does not require regular cleaning under normal operating conditions.</li><li>Sight Window&mdash;Offers a view into the combustion chamber to observe the operation of the pilot and burner.</li><li>Factory-Installed Hydrojet&reg; Total Performance System&mdash;Factory-Installed Hydrojet&reg; Total Performance System&mdash;Sediment reducing device that also increases first hour delivery of hot water while minimizing temperature build-up in tank.</li><li>Vitraglas&reg; Lining&mdash;An exclusively engineered enamel formula that provides superior tank protection from the highly corrosive effects of hot water. This formula (Vitraglas&reg;) is fused to the steel surface by firing at a temperature of over 1600&deg;F (871&deg;C).</li><li>Cast Aluminum Air Intake Boot&mdash;A cast molded air intake boot provides exceptional installation durability.</li><li>Telescoping Solid Vent Kits&mdash;Multiple kits (see reverse side) allow up to 8ft. vertical and 8ft. horizontal vent lengths (horizontal termination only).</li><li>Flexible Vent Kit&mdash;The maximum vent length (horizontal and vertical) can be flexed to 100&rdquo; (horizontal termination only).</li><li>Side Connections&mdash;3/4" NPT tappings allow easy connections for space heating applications (Potable water only) (RG2DV50H6N only).</li><li>Insulation System&mdash;2" (51mm) Non-CFC foam insulation covers surrounds the tank surface, saving energy by reducing the amount of heat loss. Pedestal Base.</li><li>Water Connections&mdash;3/4" NPT factory-installed true dielectric fittings.</li><li>Factory-Installed Heat Traps.</li><li>Protective Magnesium Anode Rod.</li><li>T&P Relief Valve&mdash;Installed.</li><li>Low Restrictive Brass Drain Valve&mdash;Durable tamper proof design.</li><li>NOx Emissions &ndash; Less than 40 ng/J.</li></ul><br/><b><u>Includes:</u></b><br/><br/><ul><li>Installation of new water heater to replace similar water heater</li><li>Installation of new shutoff valve to serve new water heater</li><li>Misc pipe & fittings in order to connect new domestic hot and cold water piping as well as existing gas piping.</li><li>Installation of new through wall direct vent piping and exterior vent diffuser.</li></ul><br/><b><u>Excludes:</u></b><br/><ul><li>Carbon monoxide detectors</li><li>Pressure reducing valve</li><li>Water heater stand and / or protection bollard</li><li>Water heater pan and / or pan drain piping.</li><li>Piping of temperature and pressure relief valve to the exterior. </li></ul>

1/2" X 1/4" BRASS BUSHING (LEAD LAW COMPLIANT)

1/2 BRASS 90 ELBOW (LEAD LAW COMPLIANT)

1/2 BRASS COUPLING (LEAD FREE)

1/2" BRASS CAP (LEAD LAW COMPLIANT)

1/2" BRASS SQUARE HD CORED RAISED HEAD PLUG (LEAD LAW COMPLIANT)

1/2" BRASS TEE (LEAD LAW COMPLIANT)

1" X 3/4" BRASS BUSHING (LEAD LAW COMPLIANT)

1 IN X 3/4 IN FIP BRASS REDUCER COUPLING (LEAD LAW COMPLIANT)

1/4" OD BRASS COMPRESSION SLEEVE (FERRULE)

1/4" OD BRASS COMPRESSION UNION (1/4 OD COMP X 1/4 OD COMP)

1/4" BRASS TEE (LEAD LAW COMPLIANT)

3-1/2" BRASS COUNTERSUNK HEAD CLEANOUT PLUG

3/4" X 1/2" BRASS BUSHING (LEAD LAW COMPLIANT)

3/4" BRASS 90 ELBOW (LEAD LAW COMPLIANT)

3/4" BRASS COUPLING (LEAD LAW COMPLIANT)

3/4 BRASS CAP (LEAD LAW COMPLIANT)

3/4" BRASS CORED SQUARE HEAD PLUG (LEAD LAW COMPLIANT)

3/4 IN BRASS STREET 90 ELBOW (LEAD LAW COMPLIANT)

3/4" BRASS TEE (LEAD LAW COMPLIANT)

3/4" BRASS UNION (LEAD LAW COMPLIANT)

3/8 OD BRASS COMPRESSION X 1/2 BRASS FIP COMPLETE ADAPTER (LEAD LAW COMPLIANT)

3/8 OD BRASS COMPRESSION X 1/2 BRASS MIP COMPLETE ADAPTER (LEAD LAW COMPLIANT)

3/8" OD X 1/4" OD BRASS COMPRESSION UNION

3/8IN X 1/4IN FEMALE COMPRESSION X TUBE ADAPTER

3/8" BRASS THREADED COUPLING

3/8" OD BRASS COMPRESSION CAP